X-Link PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
This manual applies to the following models:
3UA Multiview CONTROLER ( Optional Front Panal,LCD Console )
3UB Multiview CONTROLER ( Optional Front Panal,LCD Console )
8U Multiview CONTROLER ( Optional Front Panal )
8U-S Multiview CONTROLER( Optional Front Panal )
12U Multiview CONTROLER
LED Very-large Dot Matrix Screen Multiview CONTROLER ( K Series )
Monitoring Multiview CONTROLER ( N Series )
3D Multiview CONTROLER ( 3D Series )
4K Multiview CONTROLER (4k Series )
IMPORTANT NOTICE
The company reserves the right to update the manual according to improvement of products
without any prior notice.
In the process of using, if any content in this manual is inconsistent with actual products or there
is any further question during use, please contact document information department of our
company.
Please read this manual carefully before using the CONTROLER and properly file it after
reading for future reference. Pictures are for reference only, subject to our available products.
Please pay close attention to those with the Icon of in the article.
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
Contents
I Safety guidelines .........................................................................................................................1
II Introduction of Function about Multiview CONTROLER ..................................................2
1. Introduction of Multiview CONTROLER.............................................................................2
2. Exclusive Features of Multiview CONTROLER ..................................................................4
III Hardware connection ..............................................................................................................7
1. Hardware connection diagram ...............................................................................................7
2. Back panel interface signal diagram......................................................................................8
3. Instruction of port ................................................................................................................10
(1) Video input signal ......................................................................................................10
(2) Video output signal ....................................................................................................10
(3) Control port signal......................................................................................................10
IV Software operation ................................................................................................................11
1. Brief introduction.................................................................................................................11
2. Uncompressed installation ...................................................................................................12
3. Communication connection .................................................................................................12
4. User Login ...........................................................................................................................16
(1) Administrator User Login ..........................................................................................16
(2) Operator User Login ..................................................................................................18
5. Operation process of Multiview...........................................................................................26
(1) Output resolution setting ............................................................................................16
(2) Displayer layout settings ............................................................................................18
(3) Multi-window Settings...............................................................................................20
(4) Multi-window Basic operation...................................................................................21
(5) Scene player (scene auto switching) ..........................................................................23
V Front panel button operation ............................................................................................26
1. Front panel button diagram..................................................................................................26
2. Key Operating Instructions ..................................................................................................26
(1)Control button .............................................................................................................27
(2)Numeric keys...............................................................................................................27
(3)Key operation ..............................................................................................................27
VI Common failure ...............................................................................................................30
VII Specification parameters ................................................................................................30
VIII Other reference documents...........................................................................................31
Appendix ..................................................................................................................................32
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
- 1 -
I Safety guidelines
Danger High Voltage. There is a hazard of high pressure inside this
product, non-professional maintenance personnel are forbidden to open
the device! Beware of electric shock!
Use the power correctly. Working voltage of this product is 220V, please
ensure using the power correctly.
Ground and use the fuse correctly. This product connects to the ground
plane with earth conductors of power line, please don't connect earth
wires to the high pressure.
Keep ventilation. Maintain adequate ventilation for the device, the gap
between front& rear panels and the side should be at least 20cm.
Moisture proof. Please make sure the device is placed in a dry
environment.
Handle with care. There are precision components inside the product,
please handle with care.
Waterproof &foreign body proof. Any liquid, metal fragments, or other
irrelevant substances are prohibited to enter the device.
Put it away from the inflammable and explosive dangerous goods.
II Introduction of Multiview CONTROLER
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 2 -
This chapter includes:
Introduction of Multiview CONTROLER
Exclusive Features of Multiview CONTROLRE
1. Introduction of Multiview CONTROLER
Multiview CONTROLER is also called big screen processor and display wall CONTROLER etc.
The main function is to splice multiple display units together into a logic displayer of ultrahigh
resolution, and to realize multiple screens and scenarios of optional position and size through opening
windows on the basis of this ultrahigh-resolution displayer, which can also ensure that image quality in
each screen is excellent. It can show the entire electronic map, geographical information system,
industrial flow chart and industrial monitoring information and other data of ultrahigh resolution.
Base Type(A Series )3U、8U、12U Product Figure,as shown in the following picture:
Base Type Product Figure I（3U、8U、12U）
High-end type(U Series )3U LCD Controller Product Figure,as shown in the following picture:
3U LCD Controller Product Figure II
Mid-Range(K Series )3U Front Panal Product Figure,as shown in the following picture:
3U LCD Front Panal Figure III
Mid-Range(K Series )8U Front Panal Product Figure,as shown in the following picture:
8U LCD Front Panal Figure IV
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 4 -
2. Exclusive Features of Multiview CONTROLER
The company's multi-screen processor has the following exclusive features:
A. Pure hardware structure of FPGA, steady and reliability
With excellent image processing performance, completely avoid troubles caused by the slow
starting speed of PC, hardware conflict and computer virus. Mean Time Between Failure
（MTBF）>30000. It can work continuously for more than 1 years.
B. Support multiple video signals, on-demand distribution
It supports DVI, HDMI, VGA, AV, SDI, H264 and other video signal for accessing, users can
find any collocation as required, meeting individual requirements of different areas.
C. Flexible board design, random combinations; support hot plug, convenient maintenance
Removable board card matches with cases of different sizes, which can fully meet system
requirements of different sizes. Cases make space for expanding and reducing capacity at any time. It
is designed with exclusive card channel, system modules, such as input card, output card, control card,
fan and power supply, are all independent plug-in design, truly achieving the real-time on-line
replacement and convenient maintenance.
D. Multi-input videos roaming and overlaying, no regional and hierarchical constraints
Support multi-input videos to open multiple active windows in optional position in full screen, all
windows are allowed to roam free, overlap, magnify and narrow down, no regional and hierarchical
constraints, and no size and proportion limits.
E. Output synchronization and double-buffer technology
Realize seamless switching between scenario plans without limit to the number, truly achieving
synchronous display of screens, ensure no tear, no flicker, no blue screen, no stationary state and other
abnormal phenomena.
F. Arbitrary cutting function of input videos, support for cutting processing of any size
Arbitrary cutting function of any input video has been specially developed for this product
according to different scenarios and requirements of users. Users can cut and shape any part of screen
image freely with convenient operation of the software according to display requirements, all the
images are independently displayed.
G. Output mapping function makes construction more flexible
Realize the connection between devices and display units without one-to-one correspondence
between wires, which can be adjusted in the software freely.
H. Support special splicing. It can perfectly support various display units, realize special
display effect
In large-scale exhibitions, enterprise propaganda, stages, bars and other places, users can achieve
effects shot by using the functions of special effect and special shape. This device support any splicing
combination of display units, special-shaped splicing of LCD, DLP, PDP and LED display unit of any
resolution.
I. Pane processing technology
For traditional splicing technology, when display units with gap (. LCD \ DLP \ PDP, etc.) are
used to present pictures, the picture at the gap between two display units will be divided because of
imaging failure, resulting in picture’s breaking and deformation. X-LINK’s pane processing
technology shields the picture’s part that is covered by gap between display units through precision
adjustment for pixels, achieving smooth and intuitive display.
J. The unique advanced subtitle function makes the display more perfect
It can update and display dynamic text messages in real time according to customer needs, such as
the weather forecast and urgent message etc. The subtitle function helps users to mark video sources
properly, which not only displays images but also increases the function of text information display.
K. Mask overlapping function supports the overlapping of customized shapes. Users can
customize special effects freely
The use of mask of special effects can create a richer screen effect.
L. The preview and video echoed function greatly helps users to monitor the video
Video content displaying on the wall can be viewed in advance before playing by the software,
and can be viewed remotely during playing.
M. Local-storage presupposition for unlimited scenarios facilitates to read and call at any
time
Support the uncapped scene storage, with optional digital control panel, which can facilitate the
application of "on-duty automatic inspection" on the areas of manual switch, auto rotation and
convenient monitoring etc.
N. Digital control panel is helpful to the scene switching
Exclusively developed processor with digital control panel, using the experience of the buttons'
superior characteristics of matrix equipment, is specially for splicing in LED screen of super large dot
matrix, realizing the fast and convenient scene switching.
O. Optional embedded PC operating system
Design the embedded industrial PC motherboard into board card that can be inserted into the
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 6 -
device, so as to integrate PC into the processor to reduce users' trouble to connect it to PC. Users can
install operating system and common software in the card, which can be used for playing video.
perfectly combining functions of external splicer of pure hardware architecture and splicer of software
architecture.
P. Multi-screen interaction
Multi-screen interaction refers to the interaction of images, videos and all kinds of documentation
resources among cellphone, tablet PC and large screen wall. It is a much "cool" function. It can bring
users excellent experience, fun, convenience and it is simple, easy to use, playing the fun of touch to
the limit.
Q. Support coordinated control among devices, such as startup & shutdown of splicing wall,
matrix switching and PTZ control etc.
R. Support customized development.
III Hardware connection
This chapter includes:
Hardware connection diagram
Back panel interface signal diagram
Device supports video input,output and control port signals
1. Hardware connection diagram
The typical instance diagram of hardware connection is shown below, it can access various signal
sources, such as cameras, DVDs, notebook computers, Blue-ray DVDs, PCs, Webcam etc., and then
transmit them to the display wall.
Figure 1 Typical instance diagram of hardware connection
The installation of this device is very simple; please install it according to the following
instructions.
1. Disconnect main power of the system, and shut down powers of this device, each display unit
and auxiliary devices;
2. Place the device into the cabinet or a steady worktable, direct the back panel toward the
operating personnel, and keep good ventilation.
3. According to figure 1, connect the video cable, network cable(serial line) and power cord to the
response interface of the device.
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 8 -
4. After checking and ensuring there is no problem, turn on the power of each screen, each
auxiliary device and the device to start running it with the combination of the control software on PC.
Note: please make sure that the power of each device is disconnected and ensure all
connections are correct and reliable during cable assembly.
2. Back panel interface signal diagram
3UA type multi-screen processor supports input card slots 4, output card slots 6.
Figure 2 3UA Back panel
3UB type multi-screen processor supports input card slots 6, output card slots 4.
Figure 3 3UB Back panel
8U type multi-screen processor supports 11-bit input slot, output card slots 9.
Figure 4 8U Back panel
12U-type multi-screen processor supports 22-bit input slot, output card slots 18.
Figure 5 12U Back panel
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 10 -
3. Instruction of port
(1) Video input signals
This device supports video signal inputs, as shown in the following table:
Input port Description
DVI input Digital interface, support 1920*1080@60HZ
VGA input DB-15M analog interface, support 1920*1080@60HZ
HDMI input Digital interface, support 1920*1080@60HZ
CVBS-8 input BNC interface, supported video format: PAL/NTSC/SECAM
CVBS-2 input BNC interface, supported video format: PAL/NTSC/SECAM
SDI input Serial Digital Interface, support 1920*1080@60HZ
YPbPr
High-definition color component interface,support
1920*1080@60HZ
(2) Video output signals
This device supports video signal outputs, as shown in the following table:
Output port Description
DVI output Digital interface, support digital signal 1920*1080@60HZ
VGA output
support analog signal, able to output VGA signals through the
adapter
HDMI output
Digital interface, support HD signal, able to output HDMI signals
through the adapter
(3) Control port signals
This device supports the control, as shown in the following table:
Control port Description
Network interface
Users can control the PC software via LAN or directly using a
computer.
S232/ RS485
Users can connect the related equipment devices through serial port
for joint control.
IV Software operation
This chapter includes:
Multiview brief and decompression software installation operation
Variety of communication connectivity opitions
User logon operating software,check the device operation via intelligent detection
systemvice
PC operating processes,output resolution,mult-window display layout and set a specific
operation
1. Software brief introduction
MultiView software is a new generation of visual, WYSIWYG splicer control software, the
control software application features integrated splice products, combining the characteristics of the
installation works on the development is completed. It adopts the forefront of software design
concepts, instead of the traditional splicing control software debugging complex requirements of the
splicing process to achieve automatic operation of the window control process using a WYSIWYG
interface, avoid the cumbersome and complex stitching software default process, use of personnel can
quickly master the use of the software.
Simple software interface, easy to operate, easy to understand and easy to use, just three steps can
be done by setting splicing processors. Specific operational procedures, as follows:
2. Uncompressed installation
(1) Unzip software installation package and we get the following file:
.
℃ Output resolution setting
℃ Displayer layout settings
℃ Multi-window settings
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 12 -
(2) Click it to start the installation. After the installation is completed, the program will create a
shortcut icon on the desktop, namely MultiView, and users can also see the installed in
the start menu:
[ desktop shortcut] [start menu]
Figure 6 Software schematic diagram
Note: Some security defense software will hinder the process of the installation, please exit
the security defense software temporarily for smooth installation.
3. Communication connection
There are two modes of configuration: network and serial mode.
(1) Serial mode:
Direct-connect method: Directly connect the device to PC via the serial port line. The software
will automatically recognize the serial port (Figure 7).
Figure 7 Login page I (Serial) Figure 8 Login page 2 (Ethernet)
(2) Network mode (two methods): LAN connection method and direct-connect method.
① LAN connection method
Connect via a local area network (automatic assignment of IP). It needs a server to support
automatic assignment of IP, the software will automatically recognize the device IP(Figure 8).
② Direct-connect method
Directly connect the device to PC via a crossover cable and set the local connection Ipv4
properties(Figure 9). Then restart the device, IP "" will pop up in the connection
configuration of the software, namely the device IP(Figure 10). If it fails to detect this IP, please restart
the computer.
Figure 9 the attribute interface Figure 10 Login page 3
4. User Login
Default user name is Admin, the password is blank.
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 14 -
Figure 11 PC Login page
A. Administrator User Login
MultiView login interface system default initial user name is Admin, password is blank. Click on
the "Login" button, the software began to communicate with the device, complete with the device to
synchronize information. Admin privileges can be adjusted by user rights management, different
permissions, different level of response equipment operation.
Notes:
(1) Under the Win7 environment, sometimes users need to set the software to "run as
administrator", to let the software obtain the highest authority operation.
(2) The checked "device info" stands for information of displaying device and then
manually enter the main page, the unchecked "device info" stands for information of devices
that don't display and then automatically enter the main page.
Users can clearly know the operation of entire device by printed device information, including
device temperature and cable’s connection state, etc.
Figure 12 Select device information
Figure 13 printing equipment information page
B. Operator User Login
The user selects the "operator" login page, shown in Figure 14. Users can switch keyboard
shortcuts for quick scene change with the scene, relatively complex configuration eliminates the need
for other operations, very easy to ordinary users.
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 16 -
Figure 14 Scene switch interface
5. Operation process of Multiview
Software operating procedures, including output resolution setting, the display layout setting,
multi-window operation process, basic multi-window operation, scene auto player.
(1) Output resolution setting
Output resolution settings include increasing, deleting, editing parameters of the resolution and
the test and calibration of them, the main operation flow diagram is as follow:
Display current resolution parameters, the output resolution can be achieved on testing and
verification.
Output resolution setting
℃Select the corresponding output resolution in the resolution
list and save it
℃Check the test and calibration in the current resolution
Figure 15 Output resolution setting
Select the right resolution, if there is no right one in the list, users can add the needed resolution.
In general, users should select the best resolution.
Figure 16 current output resolution Settings
If the resolution of the display device resolution parameters and parameters of the current
selection are inconsistent, you can click Edit to modify it.
View the current output resolution, check the "test" and color bar of seven colors will exist in the
large screen if the setting is successful, as shown below.
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 18 -
Figure 17 Striped test
(2) Displayer layout settings
The displayer layout settings include array settings, corresponding relation settings and array test.
The main operation flow diagram is as follows:
The number and distribution of equipment, the layout of the logical screen to be set according to
the physical display.
Displayer layout settings
℃Add the corresponding arrays according to the screen
quantity and distribution on the monitor
℃Match the arrays according to the connectivity condition
of the actual output interface in the corresponding relations
℃Check the " test" to test the corresponding
screen output in array validation
Figure 18 Displayer layout settings
Set the layout of the logical screen according to the actual screen quantity and distribution of
display units.
Figure 19 corresponding relations settings
The actual display units of logical screens can be matched based on the connectivity condition of
the actual output interface as follows:
Select the output channel and drag it to the corresponding display unit. Directly click the output
channel in the display unit to cancel it as necessary.
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 20 -
Notes:
No. 1& 2 board cards of 3UA slot support to open four windows, others support to open two
windows.
All board cards of 3UB and 8U support to open four windows.
(3) Multi-window Settings
Multi-window settings include settings of open windows and parameters and scene saving etc.
according to input video sources. The main operating flow diagram is as follows:
Open multiple windows to display multiple screens can be realized on the big screen, multiple
input sources simultaneously display, picture in picture, the picture of any size, quickly switch the
input source, and a series of partial zoom display function. When multiple windows are superimposed,
superimposed on top of the window display section information. Multiple windows can be the same
input source may also be a different input source.
Multi-window settings
℃Select the corresponding input video source to open the
window
℃Save the scene
Figure 20 Multi-window Settings
Select the input sources to be displayed, open a window in the logical screen, and then adjust the
window size and other parameters.
Note:
please refer to (4) basic operation for details.
(4) Basic operation
A. Open a window
℃ Choose the input sources in the video source list;
℃ Drag out a rectangular window from the upper left to the lower right corner directly in edit area
of logical screen with the mouse.
B. Edit the window attribute
There are two methods to edit the basic attributes of the window:
Method I: adjust the settings of the size and coordinate of the window by dragging the mouse
directly in the edit area of logical screen;
Method II: edit the window attribute directly in window attributes column.
C. Switch input sources of a window
There are two methods to switch input sources of a window when it is necessary:
Method I: Select the window that needs switch input sources, directly double click the input slot
and channel to be switched in " Video Source " for change settings;
Method II: Select the window that needs switch input sources, and then complete the switching by
clicking the input slot and channel directly in window attribute column.
D. Windows shortcuts
There are two methods to delete, cut, resize the window and change levels etc.
Method I: Select the target window and complete the operation by context menu;
Method II: Select the target window and complete the operation through the shortcut key in " Win
Prop ".
E. Window lock
When the window attribute setting is completed, users can lock it to prevent any incorrect
operation or unnecessary change by moving the cursor. Windows will be transparent and irremovable
when it is locked.
: Select the target window and click the button to lock it.
: double click the locked window at any position to select it and then click the button
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 22 -
to unlock it.
F. The window covers all over the logical screen
There are two methods to extend a window to the range covered by the grids of its four vertices,
namely the window covers all over the logical screen:
Method I: double click the mouse to move the cursor to the target window and then double click
left mouse button to complete the operation.
Method II: get a fast implementation through toolbar shortcuts of cover all over logical screen
button .
G. Open PIP(picture in picture) function
℃ Select the target input source in the Video Source;
℃ Drag out a rectangular window from the upper left to the lower right corner directly in edit area
of logical screen with the mouse.
℃ Select the target window and click the button to lock it.
℃ After the window becomes transparent, drag out a rectangular window from the upper left to
the lower right corner on top of it with the mouse.
H. Arbitrary cutting function of input video sources
Cut any part of the video source to display independently and get a fast implementation of video
clips and window refinement so as to make the focal points stand out. The specific operation is as
follows:
℃ Drag out a rectangular window from the upper left to the lower right corner directly in edit area
of logical screen with the mouse.
℃ Select the target window and click the button to cut it.
I. Delete the window:
℃Partial delete: select the target window and click the delete button in the upper right corner
of the window to delete part of it.
℃ Delete all: complete the operation by using the clear screen button .
J. Save the information to the device:
By pressing the button , users can save the configured settings into the device or save them
as default scenes to directly restore to the latest related settings when users startup the device next time,
as shown below.
Device saving can be divided into three functions, respectively are:
℃ Scene saving: click "add" to select the added scene in the left list and set the relevant
information on the right and then click "save" to complete the operation.
℃Scene covering: select the target scene to be covered and set the relevant information on the
right and then click "save" to complete the operation.
℃ Scene deleting: select the target scene to be deleted and then click "del" to complete the
operation.
Figure 21 scenes save
(5) Scene player (scene auto switching)
It is similar to scene management tools of music players, users can customize different scenes as
needed, realizing the management to the play order and time among different scenes and can change
the information freely. The main operation flow diagram is as follows:
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 24 -
Scene player interface is shown below:
Figure 22 Scene player
Key features include scene play, pause, increase switching and scene lists, delete, and switching.
Scene player
℃Tick the "start"
℃Right click the mouse to choose new list in the left list
℃Right click the mouse to insert the scene on the right playlist
℃Choose the target scene to be playing in the "scene list"
℃Click the "play" button
list".playlist
Figure 23 Scene player–scene settings
Right click and choose the new list in the left list, and then right click to choose the insert scene in
the right scene playlist.
Figure 24 Scene player–scene show
Click the button to play the video.
Note: click the button to stop the video if you need to modify or edit it.
V Front panel button operation
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 26 -
This chapter includes:
Schematic view of the front panel buttons
Key operating instruction
The main operating of keys
1. Front panel button diagram
Control panel with LCD display, status lights, operating buttons.
Figure 25 Control panel with buttons
2. Instruction of buttons
The front panel is provided with 20 keys and a Chinese / English LCD module. 20 keys are
divided into 2 functional areas, the clear functional partitioning is convenient for users to operate the
device, while the LCD module provides rich display information.
(1) Control button
The main control buttons are used to do some fast operation, features a clear, easy to operate, the
specific key functions in the following table:
Key Description Remark
Return Return function
Up Move up and delete functions
Delete Cancellation function
Shift Shift function
Test Null
Start Lighten the screen after smart wake
Down Move down
Enter Confirm function
State Null
List Null
(2)Numeric keys
After being saved in upper computer, the scene is defined as a number and then is switched by
using numeric keys.
(3)Key operation
1. Easy scene switching
Press any key to lighten LCD screen, select the scene switching by pressing "up" and "down"
keys , press "OK" to enter the next page, then select "easy switch" and press "ok" button to switch the
scenes by corresponding numeric keys according to the order to saved scenes.
Scene switching includes easy switching, list switching and number switching.
2. Device detection
Press any key to lighten LCD screen, select the "device detection" by pressing "up" and "down"
keys to view the current working condition of the device.
3. View the IP address of this device
Press any key to lighten LCD screen, select the "device information" by pressing "up" and "down"
keys, press "OK" to enter the next page, then select "view IP address of this device" and press "ok"
button to complete the operation.
VI. Common failures
Failure Reason Step
Unable to start the
device
Power line is not plugged
in properly or switch is
disconnected.
Check the input power to make sure it is properly
plugged in and the switch is connected.
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 28 -
Failure Reason Step
Internet connection
problem
Check to make sure the cable is well plugged
Failure of server DHCP
allocation
Check to make sure the device is accessed to
LAN and passes DHCP distribution IP.
Static IP setting error
No PC IP address is set when directly connecting
device with PC.
Network connection is
failed
There are same IP
addresses among other
devices in LAN
Suggest to turn off Wifi of the control computer
RS232 serial connection
problem
Check and make sure USB is properly connected.
Serial port connection
is failed
Driving issue of USB
Check and make sure the driver of USB is
properly installed.
Video cable problem
Please check and make sure the cable connected
the device with large screen is well plugged in.
No images on the large
screen
Output resolution Settings
Please check and make sure the output resolution
well match with the large screen.
Splicing dislocation on
large screen
Problem of software
configuration
Correctly configure corresponding connection
relationship between display units and output
interface of device in the corresponding
relationship settings under the interface of
"display layout" of splicing software.
Scene losses caused by
rebooting the device
Problem of SD card
Tick the device information in the login page to
check whether the SD card is damaged.
Some interfaces in the
input video source are
crossed
Problem of cable
connection
The input channels of device are not fully
connected.
After the device is
electrified, it doesn't
react or react after a
long time
Communication problem
Replace the cable in ensuring that SD isn't
damaged.
Large screen displays
for a while then turns
into red screen
Issue of user authorization
User authorization period has arrived
If you fail to eliminate the failure according to the above methods or the failure you found is
outside of the range indicated above, please contact our technical assistance.
VII Specification parameters
Item 3UA 3UB 8U 12U
Card input slot 4 6 11 22
Card output slot 6 4 9 18
HD signals 8 12 22 44
Maximum
accessible
channel
number SD signals 32 48 88 176
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 30 -
Maximum accessible screen number 12 8 18 36
Case dimension
440*300*
135mm
440*300*
135mm
440*350*
355mm
440*350*
533mm
Maximum power consumption 200W 200W 400W 750W
Maximum weight 15Kg 15Kg 30Kg 45kg
Control interface on
display wall Standard industry interface RS-485
Interface Type
RJ-45 Network interface;
Standard industry interfaceRS-232
Control protocol
Network communication protocol;
Serial communication protocol
Control type
Control software Image processing system ()
Temperature -10℃~70℃
Humidity 0-95%( No condensation)
Environmental
parameters
Elevation <1000 feet (3048 meters)
Working voltage AC110－240V 50-60HZ
Other parameters Mean time between
failures 30000 hours
VIII Other reference documents
The following table shows other documents, detailed information, if you need, please contact with
the document information department.
文件类别 文件编号 文件名称
M-001 本地 IP 设置.mp4
M-002 分辨率和对应关系设置.mp4
M-003 多窗口操作.mp4
视频演示文件
M-004 场景播放器操作演示.mp4
M-005 系统设置.mp4
M-006 新软件操作完整演示.mp4
W-001 IPC 解码卡使用说明.pdf
W-002 安卓端软件使用说明.pdf
W-003 产品使用手册.pdf
W-004 西联电子多屏幕拼接处理器控制软件详细使用
指南.pdf
W-005 技术支持文档总结
W-006 矩阵联控协议添加及使用说明.pdf
W-007 拼接墙电源控制使用说明书.pdf
W-008 软件快速操作指南.doc
W-009 上位机软件控制 LED 屏拼接说明书.pdf
W-010 设备网络连接问题.pdf
W-011 授权设置文档.pdf
操作说明文档
W-012 直连本地 IP 设置.pdf
C-001 USB 转串口驱动.rar
C-002 USB 转串口与电脑连接示意图.png
C-003
C-004
C-005 判断 usb 转串口驱动是否正常.doc
串口调试资料
C-006 判断 usb 转串口驱动是否正常试例指令.txt
控制软件 S-001 MULTIVIEW 系列控制系统软件
Thank you again for you choose our products! We are dedicated to provide best service for you!
PRODUCT MANUALS FOR MULTIVIEW CONTROLER
PRODUCT MANUALS FOR
MULTIVIEW CONTROLER
- 32 -
Appendix
1. serial port switch control of the scene (the control)
Equipment and control the computer connection diagram, shown in Figure 26.
Figure 26 device and control computer Wiring Diagram
Determine the serial number operations, as shown in Figure 27.
Figure 27 a schematic diagram of the operation to determine the serial number
Watch the CD serial control software debugging information in the C-004 ,
the specific operation as shown in Figure 28.
Figure 28 serial debugging assistant using schematic
Instruction Set
Scene 1 5553455200020001
Scene 2 5553455200020002
Scene 3 5553455200020003
Scene 4 5553455200020004
Scene 5 5553455200020005
Scene 6 5553455200020006
